Effect of Vortex Generator Angle on Fin and Tube Heat Exchanger
DOI:
https://doi.org/10.37934/arnht.16.1.8299Keywords:
Vortex Generator, CFD, Fin and TubeAbstract
In refrigeration systems, a common installed component is the fin and tube heat exchanger. The fluid that passes through the fins has lower thermal conductivity than the fluid flowing inside the tubes, resulting in high thermal resistance. To address this problem, a vortex generator was introduced in the design of the fin and tube heat exchanger. This passive approach aims to improve heat transfer within heat exchangers by promoting the mixing of hot and cold fluids, thereby improving the convection coefficient. This study seeks to investigate the impact of the longitudinal vortex on pressure drop and the increase in the convection coefficient. Through numerical simulations, the study examined seven rows of tubes at angles of attack of 5°, 10°, and 15°. The vortex generator that used in this study are rectangular winglet pairs (RWP), concave rectangular winglet pairs (CRWP), and convex rectangular winglet pairs (CRWP). It was concluded that using Concave Rectangular Winglet Pairs (CRWP) as the vortex generator shape at a 15° angle of attack led to the highest difference in convection coefficient, reaching 154.13% of the baseline case with a Reynolds value of 662. Furthermore, the use of a Rectangular Winglet Pairs (RWP) vortex generator at a 5° angle of attack and a Reynolds value of 284 resulted in the least impact on pressure drop, with an increase of 45.29% compared to the baseline case.
Downloads
References
Bergman, Theodore L., Adrienne S. Lavine, Frank P. Incropera, and David P. DeWitt. Introduction to heat transfer. John Wiley & Sons, 2011.
Sadeghianjahromi, Ali, and Chi-Chuan Wang. "Heat transfer enhancement in fin-and-tube heat exchangers–A review on different mechanisms." Renewable and Sustainable Energy Reviews 137 (2021): 110470. https://doi.org/10.1016/j.rser.2020.110470
Guattari, Claudia, Luca Evangelisti, Paola Gori, and Francesco Asdrubali. "Influence of internal heat sources on thermal resistance evaluation through the heat flow meter method." Energy and Buildings 135 (2017): 187-200. https://doi.org/10.1016/j.enbuild.2016.11.045
Awais, Muhammad, and Arafat A. Bhuiyan. "Heat and mass transfer for compact heat exchanger (CHXs) design: A state-of-the-art review." International Journal of Heat and Mass Transfer 127 (2018): 359-380. https://doi.org/10.1016/j.ijheatmasstransfer.2018.08.026
Song, KeWei, and Toshio Tagawa. "The optimal arrangement of vortex generators for best heat transfer enhancement in flat-tube-fin heat exchanger." International Journal of Thermal Sciences 132 (2018): 355-367. https://doi.org/10.1016/j.ijthermalsci.2018.06.011
Feng, Yongshi, Ruyan Xu, Yi Cao, Xin Wu, Cai Liang, and Liyuan Zhang. "Optimization of H-type finned tube heat exchangers with combinations of longitudinal vortex generator, dimples/protrusions and grooves by Taguchi method." International Communications in Heat and Mass Transfer 143 (2023): 106709. https://doi.org/10.1016/j.icheatmasstransfer.2023.106709
Wang, Chi-Chuan, Kuan-Yu Chen, Jane-Sunn Liaw, and Chih-Yung Tseng. "An experimental study of the air-side performance of fin-and-tube heat exchangers having plain, louver, and semi-dimple vortex generator configuration." International Journal of Heat and Mass Transfer 80 (2015): 281-287. https://doi.org/10.1016/j.ijheatmasstransfer.2014.09.030
Song, KeWei, and LiangBi Wang. "Effects of longitudinal vortex interaction on periodically developed flow and heat transfer of fin-and-tube heat exchanger." International Journal of Thermal Sciences 109 (2016): 206-216. https://doi.org/10.1016/j.ijthermalsci.2016.06.011
Khanjian, Assadour, Charbel Habchi, Serge Russeil, Daniel Bougeard, and Thierry Lemenand. "Effect of rectangular winglet pair roll angle on the heat transfer enhancement in laminar channel flow." International Journal of Thermal Sciences 114 (2017): 1-14. https://doi.org/10.1016/j.ijthermalsci.2016.12.010
Liang, G., M. D. Islam, N. Kharoua, and R. Simmons. "Numerical study of heat transfer and flow behavior in a circular tube fitted with varying arrays of winglet vortex generators." International Journal of Thermal Sciences 134 (2018): 54-65. https://doi.org/10.1016/j.ijthermalsci.2018.08.004
Awais, Muhammad, and Arafat A. Bhuiyan. "Heat transfer enhancement using different types of vortex generators (VGs): A review on experimental and numerical activities." Thermal Science and Engineering Progress 5 (2018): 524-545. https://doi.org/10.1016/j.tsep.2018.02.007
Li, Hung-Yi, Wan-Rong Liao, Tian-Yang Li, and Yan-Zuo Chang. "Application of vortex generators to heat transfer enhancement of a pin-fin heat sink." International Journal of Heat and Mass Transfer 112 (2017): 940-949. https://doi.org/10.1016/j.ijheatmasstransfer.2017.05.032
Lu, Gaofeng, and Xiaoqiang Zhai. "Effects of curved vortex generators on the air-side performance of fin-and-tube heat exchangers." International Journal of Thermal Sciences 136 (2019): 509-518. https://doi.org/10.1016/j.ijthermalsci.2018.11.009
Lei, Yonggang, Fang Zheng, Chongfang Song, and Yongkang Lyu. "Improving the thermal hydraulic performance of a circular tube by using punched delta-winglet vortex generators." International Journal of Heat and Mass Transfer 111 (2017): 299-311. https://doi.org/10.1016/j.ijheatmasstransfer.2017.03.101
Joardar, A., and Anthony M. Jacobi. "Heat transfer enhancement by winglet-type vortex generator arrays in compact plain-fin-and-tube heat exchangers." International journal of refrigeration 31, no. 1 (2008): 87-97. https://doi.org/10.1016/j.ijrefrig.2007.04.011
J. P. Jean-philipe, T. Vincent, and D. Pierre, “University of Liege Implementation in OpenFOAM of a Melting / Solidification Process with the Enthalpy Method Industrial Tutor : Salvador Lucas,” 2017.
U. Ansys Inc, “Ansys Fluent Theory Guide,” ANSYS Inc., USA, vol. 15317, no. November, pp. 724–746, 2013.
Wijaya, Elang Pramudya, Sanjaya Baroar Sakti Nasution, and Agil Fadhel Kurnianto. "Study on the application of particle image velocimetry with resin and rhodamine b as alternative seeding particles in pico hydro cross flow hydro turbine." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 85, no. 1 (2021): 1-11. https://doi.org/10.37934/arfmts.85.1.111
Warjito, Warjito, Budiarso Budiarso, Elang Pramudya Wijaya, Kevin Celine, and Sanjaya Baroar Sakti Nasution. "The effect of nozzle-connector angle on cross-flow turbine performance." In AIP Conference Proceedings, vol. 2376, no. 1. AIP Publishing, 2021. https://doi.org/10.1063/5.0063477
Arora, Amit, P. M. V. Subbarao, and R. S. Agarwal. "Numerical optimization of location of ‘common flow up’delta winglets for inline aligned finned tube heat exchanger." Applied Thermal Engineering 82 (2015): 329-340. https://doi.org/10.1016/j.applthermaleng.2015.02.071
Malatesta, Vinicius, Leandro F. Souza, Joseph TC Liu, and Markus J. Kloker. "Heat transfer analysis in a flow over concave wall with primary and secondary instabilities." Procedia IUTAM 14 (2015): 487-495. https://doi.org/10.1016/j.piutam.2015.03.077
Naik, Hemant, and Shaligram Tiwari. "Effect of winglet location on performance of fin-tube heat exchangers with inline tube arrangement." International Journal of Heat and Mass Transfer 125 (2018): 248-261. https://doi.org/10.1016/j.ijheatmasstransfer.2018.04.071
Syaiful, Syaiful. "Efek Longitudinal Vortex Dihasilkan dari Vortex Generator Jenis Concave Delta dan Rectangular Winglet terhadap Perbaikan Perpindahan Panas: Visualisasi Aliran/Studi Eksperimental." Jurnal Rekayasa Mesin 8, no. 3 (2017): 167-173. https://doi.org/10.21776/ub.jrm.2017.008.03.7
Downloads
Published
How to Cite
Issue
Section
