Numerical Investigations about Flow Resistance Values for Stirling Type Pulse Tube Cryocooler
DOI:
https://doi.org/10.37934/cfdl.14.6.7989Keywords:
CFD analysis, pulse tube cryocooler, viscous resistance, inertial resistance, oscillating flow, cryogenic temperatureAbstract
Pulse tube cryocoolers are extensively used for space application because of simplicity and reliability in operation. Many researchers have attempted the numerical analysis of the oscillatory flow inside the cryocooler, however, the precise predictions of the exact behavior of the gas inside the cryocooler using CFD has not yet been reported. While performing the CFD analysis of cryocooler, the values of inertial and viscous resistance coefficients play vital role and highly contributes to the pressure drop taking place in porous media. The prime objective of present work is to analyze the effect of these resistance values on performance of cryocooler. A single stage Stirling type pulse tube cryocooler model from literature is employed to perform the CFD analysis and the results obtained from the analysis are validated to ensure that methodology used for analysis is correct. The resistance values mentioned in the literature are applicable for steady and unidirectional flows. The model is further modified for the values of resistances for oscillating flow at room temperature and oscillating flow at cryogenic temperature. It is observed that performance predictions for oscillating flow at cryogenic temperature resistance values yields substantially lower temperature than all other cases. As experimental validation of this model is still not reported in literature, the reliability of accurate resistance values is not confirmed. Hence, another model of single stage Stirling type pulse tube cryocooler from literature is numerically analyzed for various operating conditions and is compared with its experimental performance, and found to be in fair agreement.
Downloads
References
Milind_D._Atrey (2020) , International Cryogenics Monograph Series , “Cryocoolers Theory and Applications”, Springer Nature Switzerland AG . https://doi.org/10.1007/978-3-030-11307-0
Radebaugh, Ray. "A review of pulse tube refrigeration." Advances in cryogenic engineering (1990): 1191-1205.
Gifford, William E., and R. C. Longsworth. "Pulse tube refrigeration progress." Advances in cryogenic engineering 10 (1965): 69-79.
Cha, J. S., S. M. Ghiaasiaan, P. V. Desai, J. P. Harvey, and C. S. Kirkconnell. "Multi-dimensional flow effects in pulse tube refrigerators." Cryogenics 46, no. 9 (2006): 658-665. https://doi.org/10.1016/j.cryogenics.2006.03.001
Harvey, Jeremy Paul. Oscillatory compressible flow and heat transfer in porous media: application to cryocooler regenerators. Georgia Institute of Technology, 2003.
Bhavin Shah, Deep Gudhka, Udeet Rangwala, Mandar Tendolkar and Arvind Deshpande, Vjti, Vjti Vjti. "Performance Investigations of Single Stage Stirling Type Pulse Tube Cryocooler with Inertance Tube Using Cfd Simulations." Proceedings of the Fortieth National Conference on Fluid Mechanics and Fluid Power December 12-14, NIT Hamirpur, Himachal Pradesh, India,2013.
Choudhari, Mahmadrafik S., B. S. Gawali, and Prateek Malwe. "Numerical Analysis of Inertance Pulse Tube Refrigerator." In IOP Conference Series: Materials Science and Engineering, vol. 1104, no. 1, p. 012008. IOP Publishing, 2021. https://doi.org/10.1088/1757-899X/1104/1/012008
Lokanath Mohanta, and M.D. Atrey, “Phasor Analysis of Pulse Tube Refrigerator Using CFD Analysis and Isothermal Model”, Indian Journal of Cryogenics, Volume 35 A, Pages 356-361, (2010)
Cha, J. S., S. M. Ghiaasiaan, and C. S. Kirkconnell. "Oscillatory flow in microporous media applied in pulse–tube and Stirling–cycle cryocooler regenerators." Experimental thermal and fluid science 32, no. 6 (2008): 1264-1278. https://doi.org/10.1016/j.expthermflusci.2008.02.008
Landrum, E. C., T. J. Conrad, S. M. Ghiaasiaan, and Carl S. Kirkconnell. "Hydrodynamic parameters of mesh fillers relevant to miniature regenerative cryocoolers." Cryogenics 50, no. 6-7 (2010): 373-380. https://doi.org/10.1016/j.cryogenics.2010.01.017
Pathak, M. G., V. C. Patel, S. M. Ghiaasiaan, T. I. Mulcahey, B. P. Helvensteijn, A. Kashani, and J. R. Feller. "Hydrodynamic parameters for ErPr cryocooler regenerator fillers under steady and periodic flow conditions." Cryogenics 58 (2013): 68-77. https://doi.org/10.1016/j.cryogenics.2013.10.002
Perrella, Matthew, and S. Mostafa Ghiaasiaan. "Hydrodynamic resistance parameters of regenerator filler materials at cryogenic temperatures." Cryogenics 117 (2021): 103320. https://doi.org/10.1016/j.cryogenics.2021.103320
Shital Kumar Garg, B. Premachandran and Manmohan Singh, “Numerical Study of The Regenerator For a Miniature Stirling Cryocooler using The Local Thermal Equilibrium (LTE) and The Local Thermal Non-equilibrium (LTNE) Models”, Thermal Science and Engineering Progress 11,150–161,2019. https://doi.org/10.1016/j.tsep.2019.03.005
Kumar, Pankaj, A. K. Gupta, R. K. Sahoo, and D. P. Jena. "Numerical investigation of a 3D inertance pulse tube refrigerator from design prospective." Cryogenics 98 (2019): 125-138. https://doi.org/10.1016/j.cryogenics.2018.12.004
Tendolkar, M. V., K. G. Narayankhedkar, and M. D. Atrey. "Performance Comparison of Stirling-Type Single-Stage Pulse Tube Refrigerators of Inline and ‘U’Configurations." In Proceedings of 15th International Cryocooler Conference, pp. 209-215. 2008.
H K Versteeg and W Malalasekera, “An Introduction to Computational Fluid Dynamics”, Pearson Education Limited, 2007.
NIST Chemistry WebBook, NIST Standard reference data
ANSYS Fluent User’s guide, Release 12.0, 2009-01-29
