Thermal Resistance and Pressure Drop Minimization for a Micro-gap Heat Sink with Internal Micro-fins by Parametric Optimization of Operating Conditions
DOI:
https://doi.org/10.37934/cfdl.13.12.100112Keywords:
Thermal resistance, wall heat flux, pumping power, void fractionAbstract
In recent years, researchers are investigating several potential applications of two-phase flow in micro-gap heat sinks; electronic cooling is one of them. Further, internal micro-fins are used to enhance the heat transfer rate. However, the pressure drop penalty due to small gap height and fin surfaces is a major concern. Hence, minimization of thermal resistance and pressure drop is required. In this paper, effects of operating conditions, e.g., wall heat flux, pumping power, and inlet void fraction, on total thermal resistance and pressure drop in a micro-gap heat sink with internal micro-fins of rectangular and triangular profiles have been investigated by numerical analysis for the R-134a coolant. Furthermore, optimization of these parameters has been carried out by response surface methodology. Simulation results show that rectangular micro-fins show superior performance compared to triangular fins in reducing thermal resistance. Finally, for an optimum condition (7.1202×10-5 W pumping power, 1.2×107 Wm-2 heat flux, and 0.03 inlet void fraction), thermal resistance and pressure drop are reduced by 56.3% and 87.2%, respectively.
Downloads
References
Mishra, Umesh, and Jasprit Singh. Semiconductor device physics and design. Springer Science & Business Media, 2007.
Wang, Yuan, Khellil Sefiane, and Souad Harmand. "Flow boiling in high-aspect ratio mini-and micro-channels with FC-72 and ethanol: Experimental results and heat transfer correlation assessments." Experimental thermal and fluid science 36 (2012): 93-106. https://doi.org/10.1016/j.expthermflusci.2011.09.001
Tuckerman, David B., and Roger Fabian W. Pease. "High-performance heat sinking for VLSI." IEEE Electron device letters 2, no. 5 (1981): 126-129. https://doi.org/10.1109/EDL.1981.25367
Alam, Tamanna, Poh Seng Lee, Christopher R. Yap, and Liwen Jin. "Experimental investigation of microgap cooling technology for minimizing temperature gradient and mitigating hotspots in electronic devices." In 2011 IEEE 13th Electronics Packaging Technology Conference, pp. 530-535. IEEE, 2011. https://doi.org/10.1109/EPTC.2011.6184478
Alam, Tamanna, Poh Seng Lee, Christopher R. Yap, and Liwen Jin. "A comparative study of flow boiling heat transfer and pressure drop characteristics in microgap and microchannel heat sink and an evaluation of microgap heat sink for hotspot mitigation." International Journal of Heat and Mass Transfer 58, no. 1-2 (2013): 335-347. https://doi.org/10.1016/j.ijheatmasstransfer.2012.11.020
Akbar, Ronald, A. S. Pamitran, and J. T. Oh. "Two-Phase Flow Boiling Heat Transfer Coefficient with R290 in Horizontal 3 mm Diameter Mini Channel." Journal of Advanced Research in Experimental Fluid Mechanics and Heat Transfer 3, no. 1 (2021): 1-8.
Ahmed, Shugata, Ahmad Faris Ismail, Erwin Sulaeman, and Muhammad Hasibul Hasan. "A critical assessment on evaporative cooling performance of micro finned micro gap for high heat flux applications." ARPN Journal of Engineering and Applied Sciences 11, no. 1 (2016): 313-336.
Ahmed, Shugata, Ahmad Faris Ismail, Erwin Sulaeman, and Muhammad Hasibul Hasan. "A Comparative Analysis of Flow Boiling in Micro-Gaps with Internal Micro-Fins of Rectangular and Triangular Profiles." International Journal of Applied Engineering Research 11, no. 4 (2016): 2364-2372.
Ahmed, Shugata, Muhammad Hasibul Hasan, Ahmad Faris Ismail, and Erwin Sulaeman. "Effect of geometrical parameters on boiling heat transfer and pressure drop in micro finned micro gap." ARPN Journal of Engineering and Applied Sciences 11, no. 1 (2016): 297-302.
Ahmed, Shugata, Ahmad Faris Ismail, Erwin Sulaeman, and Muhammad Hasibul Hasan. "Study on turbulent characteristics of flow boiling in a micro gap under the influence of surface roughness and micro fins." ARPN Journal of Engineering and Applied Sciences 11, no. 1 (2016): 410-414.
Ahmed, S., E. Sulaeman, Ahmad Faris Ismail, and Muhammad Hasibul Hasan. “Two-Phase Fin-Induced Turbulent Cooling for Electronic Devices Using Heat Pump Associated Micro-Gap Heat Sink.” International Journal of Engineering & Technology, vol. (3.13), (2018): 113-122. https://doi.org/10.14419/ijet.v7i3.13.16336
Ahmed, Shugata, Ahmad Faris Ismail, Erwin Sulaeman, and Muhammad Hasibul Hasan. "Experimental Correlation for Flow-boiling Heat Transfer in a Micro-gap Evaporator with Internal Micro-fins." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 54, no. 1 (2019): 1-8.
Lin, Yuhao, Yang Luo, Evelyn N. Wang, Wei Li, and W. J. Minkowycz. "Enhancement of flow boiling heat transfer in microchannel using micro-fin and micro-cavity surfaces." International Journal of Heat and Mass Transfer 179 (2021): 121739. https://doi.org/10.1016/j.ijheatmasstransfer.2021.121739
Yin, Liaofei, Peixue Jiang, Ruina Xu, and Haowei Hu. "Water flow boiling in a partially modified microgap with shortened micro pin fins." International Journal of Heat and Mass Transfer 155 (2020): 119819. https://doi.org/10.1016/j.ijheatmasstransfer.2020.119819
Li, Y. F., G. D. Xia, D. D. Ma, J. L. Yang, and W. Li. "Experimental investigation of flow boiling characteristics in microchannel with triangular cavities and rectangular fins." International Journal of Heat and Mass Transfer 148 (2020): 119036. https://doi.org/10.1016/j.ijheatmasstransfer.2019.119036
Liao, Wun-Rong, Liang-Han Chien, Mohammad Ghalambaz, and Wei-Mon Yan. "Experimental study of boiling heat transfer in a microchannel with nucleated-shape columnar micro-pin-fins." International Communications in Heat and Mass Transfer 108 (2019): 104277. https://doi.org/10.1016/j.icheatmasstransfer.2019.104277
Khan, Waqar Ahmed, M. M. Yovanovich, and J. R. Culham. "Optimization of microchannel heat sinks using entropy generation minimization method." In Twenty-Second Annual IEEE Semiconductor Thermal Measurement And Management Symposium, pp. 78-86. IEEE, 2006.
Chen, Chien-Hsin. "Forced convection heat transfer in microchannel heat sinks." International Journal of Heat and Mass Transfer 50, no. 11-12 (2007): 2182-2189. https://doi.org/10.1016/j.ijheatmasstransfer.2006.11.001
Asgari, Omid, and Mohammad Hassan Saidi. "Approximate method of determining the optimum cross section of microhannel heat sink." Journal of mechanical science and technology 23, no. 12 (2009): 3448-3458. https://doi.org/10.1007/s12206-009-1018-8
Kim, Dong-Kwon, Jaehoon Jung, and Sung Jin Kim. "Thermal optimization of plate-fin heat sinks with variable fin thickness." International Journal of Heat and Mass Transfer 53, no. 25-26 (2010): 5988-5995. https://doi.org/10.1016/j.ijheatmasstransfer.2010.07.052
Baodong, Shao, Wang Lifeng, Li Jianyun, and Cheng Heming. "Multi‐objective optimization design of a micro‐channel heat sink using adaptive genetic algorithm." International Journal of Numerical Methods for Heat & Fluid Flow (2011). https://doi.org/10.1108/09615531111108512
Hung, Tu-Chieh, Wei-Mon Yan, Xiao-Dong Wang, and Yu-Xian Huang. "Optimal design of geometric parameters of double-layered microchannel heat sinks." International Journal of Heat and Mass Transfer 55, no. 11-12 (2012): 3262-3272. https://doi.org/10.1016/j.ijheatmasstransfer.2012.02.059
Adham, Ahmed Mohammed, Normah Mohd-Ghazali, and Robiah Ahmad. "Optimization of an ammonia-cooled rectangular microchannel heat sink using multi-objective non-dominated sorting genetic algorithm (NSGA2)." Heat and Mass transfer 48, no. 10 (2012): 1723-1733. https://doi.org/10.1007/s00231-012-1016-8
Hirt, Cyril W., and Billy D. Nichols. "Volume of fluid (VOF) method for the dynamics of free boundaries." Journal of computational physics 39, no. 1 (1981): 201-225. https://doi.org/10.1016/0021-9991(81)90145-5
Orszag, S. A., V. Yakhot, and W. S. Flanney. "Renormalization group modeling and turbulence, in international conference on near-wall turbulent flows." In Proceedings of the International Symposium on Mathematical Modeling of Turbulent Flows. Tokyo, Japan. 1995.
Touaibi, Rabah, and Hasan Koten. "Energy Analysis of Vapor Compression Refrigeration Cycle Using a New Generation Refrigerants with Low Global Warming Potential." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 87, no. 2 (2021): 106-117. https://doi.org/10.37934/arfmts.87.2.106117
Gunnasegaran, Prem, H. A. Mohammed, N. H. Shuaib, and Rahman Saidur. "The effect of geometrical parameters on heat transfer characteristics of microchannels heat sink with different shapes." International communications in heat and mass transfer 37, no. 8 (2010): 1078-1086. https://doi.org/10.1016/j.icheatmasstransfer.2010.06.014
Zhao, Yuan, Majid Molki, Michael M. Ohadi, and S. V. Dessiatoun. Flow boiling of CO in microchannels. Univ. of Maryland, College Park, MD (US), 2000.
Lee, Han Ju, and Sang Yong Lee. "Heat transfer correlation for boiling flows in small rectangular horizontal channels with low aspect ratios." International Journal of Multiphase Flow 27, no. 12 (2001): 2043-2062. https://doi.org/10.1016/S0301-9322(01)00054-4
Bertsch, Stefan S., Eckhard A. Groll, and Suresh V. Garimella. "Effects of heat flux, mass flux, vapor quality, and saturation temperature on flow boiling heat transfer in microchannels." International Journal of Multiphase Flow 35, no. 2 (2009): 142-154. https://doi.org/10.1016/j.ijmultiphaseflow.2008.10.004
Hung, Tu-Chieh, and Wei-Mon Yan. "Enhancement of thermal performance in double-layered microchannel heat sink with nanofluids." International Journal of Heat and Mass Transfer 55, no. 11-12 (2012): 3225-3238. https://doi.org/10.1016/j.ijheatmasstransfer.2012.02.057
