Effect of Angle of Turn on Loss Characteristics and Flow Rectification of Curve Diffuser
DOI:
https://doi.org/10.37934/cfdl.14.1.3851Keywords:
Curve diffuser, Pressure Recovery, Flow Uniformity, Angle of TurnAbstract
Curve diffuser is often used in HVAC and wind tunnel systems to provide pressure recovery and avoid excessive energy loss to the surrounding environment. Performance of curve diffuser is disturbed mainly by the presences of flow separation and secondary flow vortices occurred due to the effect of turning angle, in which scarce literature found. In this study, the effect of turning angle from 30° to 180° configured with an area ratio of 1.60 to 4.00 and inflow Reynolds number of 5.934x104 – 1.783x105 on loss characteristics and flow rectification of curve diffuser is investigated with optimum configuration is proposed. Performance of curve diffuser is evaluated in terms of pressure recovery and flow uniformity using ANSYS CFD equipped with validated Standard k-ɛ model (ske) and enhanced wall treatment of y+ = 1.2 - 1.7. Results show that performance of pressure recovery and flow uniformity decreases respectively by 85.71% and 45.84% as the angle of turn increases from 30° to 180°. Curve diffuser with minimum angle of turn 30o, optimum area ratio 2.16 and intermediate Rein 8.163x104 turns out to be the best configuration to provide pressure recovery of 0.399 and flow uniformity of 3.630 m/s.
Downloads
References
Fox, Robert W., and S. J. Kline. "Flow regimes in curved subsonic diffusers." J. Fluids Eng. Trans. ASME 84, (1962): 303-312. https://doi.org/10.1115/1.3657307
Sedlár, Milan, and Jaromır Prıhoda. "Investigation of flow phenomena in curved channels of rectangular crosssection." Engineering Mechanics 14, no. 6 (2007): 387-397.
Chong, T. P., P. F. Joseph, and P. O. A. L. Davies. "A parametric study of passive flow control for a short, high area ratio 90deg curved diffuser." Journal of Fluids Engineering 130, no. 11 (2008). https://doi.org/10.1115/1.2969447
Nguyen, Cuong K., Tuan D. Ngo, Priyan A. Mendis, and John CK Cheung. "A flow analysis for a turning rapid diffuser using CFD." J. Wind Eng 108, (2006).
Nordin, Normayati, Vijay R. Raghavan, Safiah Othman, and Zainal Ambri Abdul Karim. "Compatibility of 3-D turning diffusers by means of varying area ratios and outlet-inlet configurations." ARPN Journal of Engineering and Applied Sciences 7, no. 6 (2012): 708-713.
Nordin, Normayati, Vijay R. Raghavan, Safiah Othman, and Zainal Ambri Abdul Karim. "Numerical investigation of turning diffuser performance by varying geometric and operating parameters." In Applied Mechanics and Materials, vol. 229, pp. 2086-2093. Trans Tech Publications Ltd, 2012. https://doi.org/10.4028/www.scientific.net/AMM.229-231.2086
Nordin, Normayati, Zainal Ambri Abdul Karim, Safiah Othman, and Vijay R. Raghavan. "The performance of turning diffusers at various inlet conditions." In Applied Mechanics and Materials, vol. 465, pp. 597-602. Trans Tech Publications Ltd, 2014. https://doi.org/10.4028/www.scientific.net/AMM.465-466.597
Nordin, Normayati, Zainal Ambri Abdul Karim, Safiah Othman, and Vijay R. Raghavan. "Effect of varying inflow reynolds number on pressure recovery and flow uniformity of 3-D turning diffuser." In Applied Mechanics and Materials, vol. 699, pp. 422-428. Trans Tech Publications Ltd, 2015. https://doi.org/10.4028/www.scientific.net/AMM.699.422
Nordin, Normayati, and SERI ISKANDAR BANDAR. "Performance investigation of turning diffusers at various geometrical and operating parameters." PhD diss., Universiti Teknologi PETRONAS, 2016.
Tham, Wei Xian, Normayati Nordin, Azian Hariri, Nurul Fitriah Nasir, Norasikin Mat Isa, Musli Nizam Yahya, and Suzairin Md Seri. "Asymptotic computational fluid dynamic (ACFD) study of three-dimensional turning diffuser performance by varying angle of turn." International Journal of Integrated Engineering 11, no. 5 (2019): 109-118. https://doi.org/10.30880/ijie.2019.11.05.015
Rasidi, Shamsuri, Suzairin Md Seri, Normayati Nordin, Muhammad Zahid Shariff, Nurul Fitriah Nasir, Sharifah Adzila, and Raudhah Othman. "Numerical Investigation of 180o Curved Diffuser Performance by Varying Geometrical and Operating Parameters." CFD Letters 12, no. 7 (2020): 100-109. https://doi.org/10.37934/cfdl.12.7.100109
Huang, Lim Gim, Normayati Nordin, Lim Chia Chun, Nur Shafiqah Abdul Rahim, Shamsuri Mohamed Rasidi, and Muhammad Zahid Firdaus Shariff. "Effect of Turbulence Intensity on Turning Diffuser Performance at Various Angle of Turns." CFD Letters 12, no. 1 (2020): 48-61.
Kumaraswamy, Rakesh, Karthikeyan Natarajan, and R. B. Anand. "CFD Analysis of Flow and Performance Characteristics of a 90° curved Rectangular Diffuser: Effects of Aspect Ratio and Reynolds Number." International Journal of Turbo & Jet-Engines (2019). https://doi.org/10.1515/tjj-2019-0011
Zhang, Wei-Li, Doyle D. Knight, and Don Smith. "Automated design of a three-dimensional subsonic diffuser." Journal of Propulsion and Power 16, no. 6 (2000): 1132-1140. https://doi.org/10.2514/6.2000-665
Khong, Y. T., N. Nordin, S. M. Seri, A. N. Mohammed, A. Sapit, I. Taib, K. Abdullah, A. Sadikin, and M. A. Razali. "Effect of turning angle on performance of 2-D turning diffuser via Asymptotic Computational Fluid Dynamics." In IOP Conference Series: Materials Science and Engineering, vol. 243, no. 1, p. 012013. IOP Publishing, 2017. https://doi.org/10.1088/1757-899X/243/1/012013
Shariff, Muhammad Zahid Firdaus, Normayati Nordin, Lim Chia Chun, Shamsuri Mohamed Rasidi, Raudhah Othman, and Sharifah Adzila. "Development of Performance Correlations using ACFD Method for 2-D Curved Diffuser." CFD Letters 12, no. 8 (2020): 1-16. https://doi.org/10.37934/cfdl.12.8.116
El-Askary, W. A., and M. Nasr. "Performance of a bend–diffuser system: Experimental and numerical studies." Computers & fluids 38, no. 1 (2009): 160-170. https://doi.org/10.1016/j.compfluid.2008.01.003
Suryadi, Aji. "Compressor Piping Design Effect on Vibration Data." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 88, no. 1 (2021): 94-108. https://doi.org/10.37934/arfmts.88.1.94108
Omar, Hossin, Suliman Alfarawi, Azeldin El-sawi, and Hassan Alobeidy. "Study the Effect of Baffle Spacing on Heat Transfer and Pressure Drop in Shell and Tube Heat Exchanger." Journal of Advanced Research in Numerical Heat Transfer 6, no. 1 (2021): 22-30.
Gan, Guohui, and Saffa B. Riffat. "Measurement and computational fluid dynamics prediction of diffuser pressure-loss coefficient." Applied energy 54, no. 2 (1996): 181-195. https://doi.org/10.1016/0306-2619(95)00078-X
Wang, Yi-Chun, Jui-Cheng Hsu, Ping-Chi Kuo, and Yung-Chun Lee. "Loss characteristics and flow rectification property of diffuser valves for micropump applications." International Journal of Heat and Mass Transfer 52, no. 1-2 (2009): 328-336. https://doi.org/10.1016/j.ijheatmasstransfer.2008.06.010
Mohamed, Mohamed S., Berge Djebedjian, and M. M. Rayan. "Experimental and Numerical Studies of Flow in a Logarithmic Spiral Curved Diffuser." In Proceedings, FEDSM ‘2000, ASME Fluids Engineering Summer Meeting Conference, pp. 1-8. 2000.
Gopaliya, Manoj Kumar, and K. K. Chaudhary. "CFD analysis of performance characteristics of Y-shaped diffuser with combined horizontal and vertical offsets." Aerospace Science and Technology 14, no. 5 (2010): 338-347. https://doi.org/10.1016/j.ast.2010.02.008
Gopaliya, Manoj Kumar, Piyush Goel, Sunil Prashar, and Anil Dutt. "CFD analysis of performance characteristics of S-shaped diffusers with combined horizontal and vertical offsets." Computers & fluids 40, no. 1 (2011): 280-290. https://doi.org/10.1016/j.compfluid.2010.09.027
El-Askary, W. A., and M. Nasr. "Performance of a bend–diffuser system: Experimental and numerical studies." Computers & fluids 38, no. 1 (2009): 160-170. https://doi.org/10.1016/j.compfluid.2008.01.003
