CFD Simulation of the Airflow Distribution Inside Cube-Grow
DOI:
https://doi.org/10.37934/cfdl.13.12.8189Keywords:
Airflow, CFD simulation, Urban farmingAbstract
Cube-Grow was developed by MARDI to promote urban agriculture to the urban population. The product enables urban people to grow their vegetables with limited space. The initial test run of the system shows that the plant growth inside the structure was below expectation. The problem arises due to a lack of airflow or improper ventilation inside the structure. Optimum ventilation or airflow is crucial for plant growth as it enhances evapotranspiration at the leaf area to promote optimum plant growth. Therefore, this study aims to increase the airflow inside the Cube-Grow and find the best location for the air hole. Computational fluid dynamics (CFD) simulation was used in this study the analyse the effect of adding an air hole to the airflow characteristic inside the Cube-Grow. CFD also was used to select the best location to place the air hole. 3 option of air hole location was analysed and the results were compared with the existing design. The initial CFD simulation results were compared with the actual measurement data before it was used for further analysis. The result shows that adding an air hole increases overall airflow inside the Cube-Grow. Option 3 was chosen as the best location for the air hole as it produces a uniform and higher airflow inside the Cube-Grow. The study proved that CFD was able to be used to optimize the design of Cube-Grow before the actual prototype was built.
Downloads
References
Shamsudin, Mad Nasir, Golnaz Rezai, and Phuah Kit Teng. "Public attitude toward urban agriculture in Malaysia: study on values and knowledge in Klang Valley." Journal of Food Products Marketing 20, no. sup1 (2014): 35-48. https://doi.org/10.1080/10454446.2014.921873
Ibrahim, L., and Siti Aisyah Salim. "The framework of urban farming towards enhancing quality of life in Malaysia." International Journal of Supply Chain Management 9, no. 1 (2020): 520-526.
Baek, Min-Seon, Sook-Youn Kwon, and Jae-Hyun Lim. "Improvement of the crop growth rate in plant factory by promoting air flow inside the cultivation." International Journal of Smart Home 10, no. 2 (2016): 63-74. https://doi.org/10.14257/ijsh.2016.10.2.07
Kitaya, Y., T. Shibuya, M. Yoshida, and M. Kiyota. "Effects of air velocity on photosynthesis of plant canopies under elevated CO2 levels in a plant culture system." Advances in space research 34, no. 7 (2004): 1466-1469. https://doi.org/10.1016/j.asr.2003.08.031
Kitaya, Y., J. Tsuruyama, T. Shibuya, M. Yoshida, and M. Kiyota. "Effects of air current speed on gas exchange in plant leaves and plant canopies." Advances in Space Research 31, no. 1 (2003): 177-182. https://doi.org/10.1016/S0273-1177(02)00747-0
Li, X., G. D. Wang, and X. Z. Xue. "Effects of different wind speeds on the growth and transpiration of potted sweet pepper in greenhouse." Chinese Journal of Agricultural Engineering 2 (2008): 214-218.
Lee, Jun Gu, Chang Sun Choi, Yoon Ah Jang, Suk Woo Jang, Sang Gyu Lee, and Yeong Cheol Um. "Effects of air temperature and air flow rate control on the tipburn occurrence of leaf lettuce in a closed-type plant factory system." Horticulture, Environment, and Biotechnology 54, no. 4 (2013): 303-310. https://doi.org/10.1007/s13580-013-0031-0
Peiro, Enrique, Antonio Pannico, Sebastian George Colleoni, Lorenzo Bucchieri, Youssef Rouphael, Stefania De Pascale, Roberta Paradiso, and Francesc Gòdia. "Air Distribution in a Fully-Closed Higher Plant Growth Chamber Impacts Crop Performance of Hydroponically-Grown Lettuce." Frontiers in Plant Science 11 (2020): 537. https://doi.org/10.3389/fpls.2020.00537
Lee, In-Bok, Jessie Pascual P. Bitog, Se-Woon Hong, Il-Hwan Seo, Kyeong-Seok Kwon, Thomas Bartzanas, and Murat Kacira. "The past, present and future of CFD for agro-environmental applications." Computers and electronics in agriculture 93 (2013): 168-183. https://doi.org/10.1016/j.compag.2012.09.006
Yusoff, Mohd Zamri, Azfarizal Mukhtar, Khai Ching Ng, and Mohamad Fariz Mohamed Nasir. "Application of Box-Behnken design with response surface to optimize ventilation system in underground shelter." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 52, no. 2 (2018): 161-173.
Mat, Sohif, Suhaimi Misha, Mohd Hafidz Ruslan, Elias Salleh, and Kamaruzzaman Sopian. "A Study of Drying Uniformity in a New Design of Tray Dryer." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 52, no. 2 (2018): 129-138.
Bartzanas, T. B. T. K. C., Thierry Boulard, and C. Kittas. "Effect of vent arrangement on windward ventilation of a tunnel greenhouse." Biosystems Engineering 88, no. 4 (2004): 479-490. https://doi.org/10.1016/j.biosystemseng.2003.10.006
Noh, Arina Mohd, Sohif Mat, and Mohd Hafidz Ruslan. "CFD simulation of temperature and air flow distribution inside industrial scale solar dryer." Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 45, no. 1 (2018): 156-164.
Lim, Tae-Gyu, and Yong Hyeon Kim. "Analysis of airflow pattern in plant factory with different inlet and outlet locations using computational fluid dynamics." Journal of Biosystems Engineering 39, no. 4 (2014): 310-317. https://doi.org/10.5307/JBE.2014.39.4.310
Niam, A. G., T. R. Muharam, S. Widodo, M. Solahudin, and L. Sucahyo. "CFD simulation approach in determining air conditioners position in the mini plant factory for shallot seed production." In AIP Conference Proceedings, vol. 2062, no. 1, p. 020017. AIP Publishing LLC, 2019. https://doi.org/10.1063/1.5086564
Mohd Noh, Arina, Muhd Akhtar Mohamad Tahir, Sohif Bin Mat and Mohd Hakimi Dzulkifli. “CFD simulation of temperature and airflow inside a shipping container size plant factory for optimal lettuce production.” Supplementary 6 (2020): n. pag. https://doi.org/10.26656/fr.2017.4(S6).039
Fan, Ruiqi, Huan Liu, Shenghan Zhou, Zhongqun He, Xin Zhang, Ke Liu, Jinxiao Wang, Qichang Yang, Yangxia Zheng, and Wei Lu. "CFD simulation of the airflow uniformity in the plant factory." In IOP Conference Series: Earth and Environmental Science, vol. 560, no. 1, p. 012074. IOP Publishing, 2020. https://doi.org/10.1088/1755-1315/560/1/012074
Li, Ning. "Comparison between three different CFD software and numerical simulation of an ambulance hall." (2015).
Zhang, Ying, Murat Kacira, and Lingling An. "A CFD study on improving air flow uniformity in indoor plant factory system." biosystems engineering 147 (2016): 193-205. https://doi.org/10.1016/j.biosystemseng.2016.04.012
Fang, Hui, Kun Li, Gang Wu, Ruifeng Cheng, Yi Zhang, and Qichang Yang. "A CFD analysis on improving lettuce canopy airflow distribution in a plant factory considering the crop resistance and LEDs heat dissipation." Biosystems Engineering 200 (2020): 1-12. https://doi.org/10.1016/j.biosystemseng.2020.08.017
